647-716-6132
Mold Inspections
Toronto Mold inspectors

Mold Inspection Standards of Practice 

The following is from the New York City Department of Health and Mental Hygiene and your Toronto Mold Inspector 

Visual Inspection

A visual inspection is the most important initial step in identifying a possible mold problem and in determining remedial strategies.  The extent of any water damage and mold growth should be visually assessed and the affected building materials identified.  A visual inspection should also include observations of hidden areas where damages may be present, such as crawl spaces, attics, and behind wallboard.  Carpet backing and padding, wallpaper, mouldings (e.g. baseboards), insulation and other materials that are suspected of hiding mold growth should also be assessed. 

Ceiling tiles, paper-covered gypsum wallboard (drywall), structural wood, and other cellulose-containing surfaces should be given careful attention during a visual inspection.  Ventilation systems should be visually checked for damp conditions and/or mold growth on system components such as filters, insulation, and coils/fins, as well as for overall cleanliness. 

Equipment such as a moisture meter or infrared camera (to detect moisture in building materials) or a boroscope (to view spaces in ductwork or behind walls) may be helpful in identifying hidden sources of mold growth, the extent of water damage, and in determining if the water source is active. 

Using personal protective equipment such as gloves and respiratory protection (e.g. N-95 disposable respirator) should be considered if assessment work might disturb mold.  Efforts should also be made to minimize the generation and migration of any dust and mold.  

 

The presence of mold growth, water damage, or musty odors should be addressed quickly.  In all instances, any sources of water must be identified and corrected and the extent of water damage and any mold growth determined.  Water-damaged materials should be removed or cleaned and dried. 

 

Environmental Sampling

Environmental sampling is not usually necessary to proceed with remediation of visually identified mold growth or water-damaged materials.  Decisions about appropriate remediation strategies can generally be made on the basis of a thorough visual inspection.  Environmental sampling may be helpful in some cases, such as, to confirm the presence of visually identified mold or if the source of perceived indoor mold growth cannot be visually identified. 

                               Watch this short mold  video

I am a  certified Mold Inspector, and Flir (ITC) Certified Level 2 Thermographer. I regularly attend seminars related to Mold and IAQ. (Indoor Air Quality)

Yes, I charge more for my services, but consider the alternative! Mold takes 24-48 hours to grow, if a moisture or water leak is missed during an inspection, mold will grow undetected.

My fee for a Mold inspection is a standard $450.00 + (Lab fees) this includes a BASIC IR scan ("Thermal Imaging") for water or moisture intrusion. It also includes an Inspection of the following items;

  • Attic ( insulation, ventilation, roof leaks)
  • Foundation
  • Gutters and Downspout
  • Grading
  • Plumbing
  • inspecting the entire home for Water/Moisture intrusion(Visually and using my IR camera)

The entire process takes approximately 2-2.5 Hours to complete. Sampling is not usually necessary to proceed with remediation of visually identified mold .  If you require sampling it is an added cost.

 

EPA Mold, Moisture and your Home Guide  Download this free pamphlet from the USEPA from your Toronto Mold Inspector

PDF Version

 MORE MOLD INFORMATION HEALTH CANADA

Information About Mold 

 

 “Inspected once, inspected right”

Tag line provided by Mr. Nick Gromicko ® founder of NACHI 

If you do not have Adobe Acrobat, click here to download it.       

 I Serve:

         Environmental engineering and construction firms

         Building contractors

         Homeowners

         Other Home inspectors

         Real estate agents

         Seniors facilities

         Industrial and commercial buildings

         Insurance professionals

         Day care, kid’s facilities  

IAC2 CertifiedMold Inspection Standards of Practice 


Certifications acquired through home inspector training from InterNACHI
 
 

Moisture and Your Home

Mold
Mold Basics
  • The key to mold control is moisture control.
  • If mold is a problem in your home, you should clean up the mold promptly and fix the water problem.
  • It is important to dry water-damaged areas and items within 24 to 48 hours to prevent mold growth.
Why is mold growing in my home?
 
Molds are part of the natural environment. Outdoors, molds play a part in nature by breaking down dead organic matter, such as fallen leaves and dead trees. But indoors, mold growth should be avoided. Molds reproduce by means of tiny spores; the spores are invisible to the naked eye and float through outdoor and indoor air. Mold may begin growing indoors when mold spores land on surfaces that are wet. There are many types of mold, and none of them will grow without water or moisture.
 
Can mold cause health problems?
 

Molds are usually not a problem indoors, unless mold spores land on a wet or damp spot and begin growing. Molds have the potential to cause health problems. Molds produce allergens (substances that can cause allergic reactions), irritants and, in some cases, potentially toxic substances (mycotoxins). Inhaling or touching mold or mold spores may cause allergic reactions in sensitive individuals. Allergic responses include hay fever-type symptoms, such as sneezing, runny nose, red eyes, and skin rash (dermatitis). Allergic reactions to mold are common. They can be immediate or delayed. Molds can also cause asthma attacks in people with asthma who are allergic to mold. In addition, mold exposure can irritate the eyes, skin, nose, throat and lungs of both mold-allergic and non-allergic people. Symptoms other than the allergic and irritant types are not commonly reported as a result of inhaling mold. Research on mold and health effects is ongoing. This article provides a brief overview; it does not describe all potential health effects related to mold exposure. For more detailed information, consult a health professional. You may also wish to consult your state or local health department.

How do I get rid of mold? Mold Spores

It is impossible to get rid of all mold and mold spores indoors. Some mold spores will be found floating through the air and in house dust. Mold spores will not grow if moisture is not present. Indoor mold growth can and should be prevented or controlled by controlling moisture indoors. If there is mold growth in your home, you must clean up the mold and fix the water problem. If you clean up the mold but don't fix the water problem, then, most likely, the mold problem will recur.
 
Who should do the cleanup?
 
This depends on a number of factors. One consideration is the size of the mold problem. If the moldy area is less than about 10 square feet (less than roughly a 3-foot by 3-foot patch), in most cases, you can handle the job yourself, following the guidelines below.
  • If there has been a lot of water damage, and/or mold growth covers more than 10 square feet, consult with an InterNACHI inspector.
  • If you choose to hire a contractor (or other professional service provider) to do the cleanup, make sure the contractor has experience cleaning up mold. Check references and ask the contractor to follow the recommendations of the EPA, the guidelines of the American Conference of Governmental Industrial Hygenists (ACGIH), or other guidelines from professional or government organizations.
  • Do not run the HVAC system if you know or suspect that it is contaminated with mold. This could spread mold throughout the building.
  • If the water and/or mold damage was caused by sewage or other contaminated water, then call in a professional who has experience cleaning and fixing buildings damaged by contaminated water.
  • If you have health concerns, consult a health professional before starting cleanup.
Tips and Techniques
 
The tips and techniques presented in this section will help you clean up your mold problem. Professional cleaners or remediators may use methods not covered here. Please note that mold may cause staining and cosmetic damage. It may not be possible to clean an item so that its original appearance is restored.
  • Fix plumbing leaks and other water problems as soon as possible. Dry all items completely.
  • Scrub mold off hard surfaces with detergent and water, and dry completely.
  • Absorbent or porous materials, such as ceiling tiles and carpet, may have to be thrown away if they become moldy. Mold can grow on or fill in the empty spaces and crevices of porous materials, so the mold may be difficult or impossible to remove completely.
  • Avoid exposing yourself or others to mold.
  • Do not paint or caulk moldy surfaces.
  • Clean up the mold and dry the surfaces before painting. Paint applied over moldy surfaces is likely to peel. If you are unsure about how to clean an item, or if the item is expensive or of sentimental value, you may wish to consult a specialist. Specialists in furniture repair and restoration, painting and art restoration and conservation, carpet and rug cleaning, water damage, and fire or water restoration are commonly listed in phone books. Be sure to ask for and check references. Look for specialists who are affiliated with professional organizations.
What to Wear When Cleaning Moldy Areas:
  • Avoid breathing in mold or mold spores. In order to limit your exposure to airborne mold, you may want to wear an N-95 respirator, available at many hardware stores and from N-95 Mask companies that advertise on the Internet. (They cost about $12 to $25.) Some N-95 respirators resemble a paper dust mask with a nozzle on the front, and others are made primarily of plastic or rubber and have removable cartridges that trap and prevent most of the mold spores from entering. In order to be effective, the respirator or mask must fit properly, so carefully follow the instructions supplied with the respirator. Please note that the Occupational Safety and Health Administration (OSHA) requires that respirators fit properly (via fit testing) when used in an occupational setting.
  • Wear gloves. Long gloves that extend to the middle of the forearm are recommended. When working with water and a mild detergent, ordinary household rubber gloves may be used. If you are using a disinfectant, a biocide such as chlorine bleach, or a strong cleaning solution, you should select gloves made from natural rubber, neoprene, nitrile, polyurethane or PVC. Avoid touching mold or moldy items with your bare hands.
  • Wear goggles. Goggles that do not have ventilation holes are recommended. Avoid getting mold or mold spores in your eyes.
How do I know when the remediation or cleanup is finished?

You must have completely fixed the water or moisture problem before the cleanup or remediation can be considered finished, based on the following guidelines:

  • You should have completed the mold removal. Visible mold and moldy odors should not be present. Please note that mold may cause staining and cosmetic damage.
  • You should have revisited the site(s) shortly after cleanup, and it should show no signs of water damage or mold growth.
  • People should have been able to occupy or re-occupy the area without health complaints or physical symptoms.
  • Ultimately, this is a judgment call; there is no easy answer. If you have concerns or questions, be sure to ask your InterNACHI inspector during your next scheduled inspection.
 
Moisture Control
 

Moisture and Mold Prevention and Control Tips

  • Moisture control is the key to mold control, so when water leaks or spills occur indoors, ACT QUICKLY. If wet or damp materials or areas are dried within 24 to 48 hours after a leak or spill happens, in most cases, mold will not grow.
  • Clean and repair roof gutters regularly.
  • Make sure the ground slopes away from the building's foundation so that water does not enter or collect around the foundation.
  • Keep air-conditioning drip pans clean and the drain lines unobstructed and flowing properly.
  • Keep indoor humidity low. If possible, keep indoor humidity below 60% relative humidity (ideally, between 30% to 50%). Relative humidity can be measured with a moisture or humidity meter, which is a small, inexpensive instrument (from $10 to $50) that is available at many hardware stores.
  • If you see condensation or moisture collecting on windows, walls or pipes, ACT QUICKLY to dry the wet surface and reduce the moisture/water source. Condensation can be a sign of high humidity.

Actions that will help to reduce humidity:

  • Vent appliances that produce moisture, such as clothes dryers, stoves, and kerosene heaters, to the outdoors, where possible. (Combustion appliances, such as stoves and kerosene heaters, produce water vapor and will increase the humidity unless vented to the outside.)
  • Use air conditioners and/or de-humidifiers when needed.
  • Run the bathroom fan or open the window when showering. Use exhaust fans or open windows whenever cooking, running the dishwasher or dishwashing, etc.

Actions that will help prevent condensation:

  • Reduce the humidity (see above).
  • Increase ventilation and air movement by opening doors and/or windows, when practical. Use fans as needed.
  • Cover cold surfaces, such as cold water pipes, with insulation.
  • Increase air temperature.
Plumbing Leaks


Testing or Sampling for Mold
 
Is sampling for mold needed? In most cases, if visible mold growth is present, sampling is unnecessary. Since no EPA or other federal limits have been set for mold or mold spores, sampling cannot be used to check a building's compliance with federal mold standards. Surface sampling may be useful to determine if an area has been adequately cleaned or remediated. Sampling for mold should be conducted by professionals who have specific experience in designing mold sampling protocols, sampling methods, and interpreting results. Sample analysis should follow analytical methods recommended by the American Industrial Hygiene Association (AIHA), the American Conference of Governmental Industrial Hygienists (ACGIH), or other professional organizations.
 
Suspicion of Hidden Mold
 
You may suspect hidden mold if a building smells moldy but you cannot see the source, or if you know there has been water damage and residents are reporting health problems. Mold may be hidden in places such as the backside of dry wall, wallpaper or paneling, the top-side of ceiling tiles, or the underside of carpets and pads, etc. Other possible locations of hidden mold include areas inside walls around pipes (with leaking or condensing pipes), the surface of walls behind furniture (where condensation forms), inside ductwork, and in roof materials above ceiling tiles (due to roof leaks or insufficient insulation).
 
Investigating Hidden Mold Problems
 
Investigating hidden mold problems may be difficult and will require caution when the investigation involves disturbing potential sites of mold growth. For example, removal of wallpaper can lead to a massive release of spores if there is mold growing on the underside of the paper. If you believe that you may have a hidden mold problem, consider hiring an experienced professional.
 
Cleanup and Biocides
 
Biocides are substances that can destroy living organisms. The use of a chemical or biocide that kills organisms such as mold (chlorine bleach, for example) is not recommended as a routine practice during mold cleanup. There may be instances, however, when professional judgment may indicate its use (for example, when immune-compromised individuals are present). In most cases, it is not possible or desirable to sterilize an area; a background level of mold spores will remain, and these spores will not grow if the moisture problem has been resolved. If you choose to use disinfectants or biocides, always ventilate the area and exhaust the air to the outdoors. Never mix chlorine bleach with other cleaning solutions or detergents that contain ammonia because toxic fumes could be produced.
 
Please note: Dead mold may still cause allergic reactions in some people, so it is not enough to simply kill the mold; it must also be removed.
 
Ten Things You Should Know About Mold
 
1. Potential health effects and symptoms associated with mold exposure include allergic reactions, asthma, and other respiratory complaints.
2. There is no practical way to eliminate all mold and mold spores in the indoor environment; the way to control indoor mold growth is to control moisture.
3. If mold is a problem in your home, you must clean up the mold and eliminate sources of moisture.
4. Fix the source of the water problem or leak to prevent mold growth.
 
5. Reduce indoor humidity (to 30% to 60%) to decrease mold growth by:
a. venting bathrooms, dryers, and other moisture-generating sources to the outside;
b. using air conditioners and de-humidifiers;
c. increasing ventilation; and
d. using exhaust fans whenever cooking, dishwashing, and cleaning.
6. Clean and dry any damp or wet building materials and furnishings within 24 to 48 hours to prevent mold growth.
 
7. Clean mold off hard surfaces with water and detergent, and dry completely. Absorbent materials that are moldy (such as carpeting and ceiling tiles) may need to be replaced.
 
8. Prevent condensation. Reduce the potential for condensation on cold surfaces (i.e., windows, piping, exterior walls, roof and floors) by adding insulation.
 
9. In areas where there is a perpetual moisture problem, do not install carpeting.
 
10. Molds can be found almost anywhere; they can grow on virtually any substance, provided moisture is present. There are molds that can grow on wood, paper, carpet, and foods.
 
Water Stains

FREE FROM MOLD
 

Toronto Mold InspectorToronto Home InspectorToronto Home Inspector is pet friendlyToronto Deck InspectorToronto Home Inspector is First time buyer friendlyToronto Mold Inspector Roof Inspector Repair Verification InspectorToronto Certified  Home InspectorToronto Commercial Building InspectorGarage Inspector Toronto

IF YOUR INSPECTOR IS NOT USING THERMAL IMAGING, YOU'RE NOT GETTING THE WHOLE PICTURE ℠

 

Call me Mario Kyriacou CHI CMI today to schedule your Inspection or for any questions or concerns.

647-716-6132 or email me torontohomeinspector@yahoo.com

Call me from 8:00am-10:00pm 7 days/week 

Protected by Copyscape Originality Checker